Installing A Bath tub
Installing A Bath tub
Blog Article
The article which follows pertaining to How to Install a Bathtub Yourself is really stimulating. Don't miss out on it.
Setting up a bath tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging task. If the old tub is easily obtainable, the project can move immediately; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bath tub, the task is a lot harder. In either case, the job is within a house handyman's abilities, although you will need a helper to vacate the old bathtub and set in the new one. See to it you have actually qualified yourself for the task and also fit attempting it. Rather than hiring a professional to take control of a halfway-completed job, it is far better to take into consideration using one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new bathtub in your bathroom if you have already purchased a brand-new bathtub as well as do not require to transform the setup of your previous water pipelines.
Your devices and also product checklist should comprise the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub until the level reviews degree.
To install taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill up the tub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Safeguard the faucet in place with the producer provided backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The former type needs to be attached to the tap finishes first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall surface between the bath as well as the tiling, causing issues with dampness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that blog post about Tools You Need to Install a New Bathtub while doing a lookup on the web. Sharing is good. You won't know, you will be helping someone out. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Get Quote
Report this page